The largest Civic Type R club forum

[1812_s]

just a few parts i have now collected



Got this DC header of Cosmic-Dan of forums and picked up from him at TDI South





Good flexi

[C2AXG]

What wrap have you used on the manifold also could you tell me the measurement between the outside of each hole like from the outside of one to the outside of the other on the sensors is it 210mm
Are you planning on running the manifold without mapping.

[1812_s]

Hi, no I'm not planning on running without map its sitting in my shed can't wait but waiting for skunk 2 inlet and then kpro may get it all done around November.......not sure about the wrap I bought it off cosmic-dan off here

[Alex-B]

The vibration from the mount inserts will always be there you just don't notice them after a while.

[1812_s]

Oh I remember it when I first got it 200 miles ago and its definetly less since then but it must be me getting used it then

[C2AXG]

Something Ile be getting used to then I have engine and gearbox poly mounts ready to go in...
More noise lol

[1812_s]

Update

Got a Tegiwa harness bar and Omp harnesses

[1qjjogim]

where did u get ur seat cover from mate , any links?

[1812_s]

Update

Thought i should clear some space so i started to get everything i had in boxes fitted

Will be fitting DC header next with k100.

H.I.D first as one of the bulbs blew anyway
Xenon 6000k 55w kit




Tegiwa Short shifter + bushes

[1812_s]

Update

JDM rear anti roll bar

A lot heavier and thicker, i have taken pictures the best i can to show a comparison for anyone interested







Goodridge braided lines and Cosworth pads

[luke beard]

coming along nicely mate :bigthumb: have you sorted your k100 yet as theres a group buy on at the mo

[1812_s]

yep im on it

[luke beard]

:bigthumb:

[keithlou]

i know the cosworth pads are brand new but how you finding them so far?

anything to compare it with? ie: ds2500 [smilie=karls_thumb.gif]

i've just put brand oem spec pads last month and they feel like shot again lol

[1812_s]

ive just put them on havent driven yet but it says to break in for 200 miles, im going out later so ill give them a little test later

[1812_s]

i know the cosworth pads are brand new but how you finding them so far?

anything to compare it with? ie: ds2500 [smilie=karls_thumb.gif]

i've just put brand oem spec pads last month and they feel like shot again lol

Cosworth pads are great however i dont have anything to compare too other than the oem spec pads that came with the car....never thought uprated pads made a difference but there great and are still good when cold. The braided lines are top aswell, im very happy

[1812_s]

Have given the car a full detail and the paint now feels incredibly smooth i used the following in below pic took me quite a while but it was worth it.









Have also purchased a scuttle tidy as my previous bodge wasnt up to standard
Great product thanks to dent-remover for that one



To finish it off i purchased a weighted skunk 2 knob of ctr-lib
It is really great a top mod.... worth every penny



In preparation for the remap i have just order some new sparks and will be doing valve clearances before fitting dc header and going to eurospec

[Liam Type-R]

Good worth while mods, will notice a difference with most of them which is alsways win. :salut:

[1812_s]

Yeah skunk knob suprised me

[nathanpar]

Have given the car a full detail and the paint now feels incredibly smooth i used the following in below pic took me quite a while but it was worth it.









Have also purchased a scuttle tidy as my previous bodge wasnt up to standard
Great product thanks to dent-remover for that one




To finish it off i purchased a weighted skunk 2 knob of ctr-lib
It is really great a top mod.... worth every penny



In preparation for the remap i have just order some new sparks and will be doing valve clearances before fitting dc header and going to eurospec

Just wondering what order you did everything in for restoring your cars body work, you fitting a rbc for your remap aswell?